30A Micro ESC
DESIGN CONCEPT Less is More Remote Controlled Car
12.99 16.99 8.99 9.99 15.99 0.00  2X COMPLETE  1.24 CARS   =   $64.95
UNIVERSAL BATTERY TRAY
PAPER CLIP BUMPER
SPACE SAVER SNAP IN SERVO
ALMOST FULL SIZE
LAST THOUGHTS
TIE DOWN SLOTS
   
THINGS YOU NEED TOO KNOW
This designs is primary built to be iterated on - its simplicity allows for anyone to make iteratation for improvement - It has a longer wheel base for stability.  Making small adjustments can really change the dynamics of the car. I look forward to seeing what people create. Good Luck - and reach out if you have any questions .  I’m on Facebook and Youtube.
DOWNLOAD STL S1.24
PERFORMANCE RECOMMENDATIONS:
FREE
CRAZY FAST
Thinner Front Arm =  more dynamic suspension Front Springs = FPV stabilizers   Axels Bearings = prevent plastic melting at speed
SNAP IN MOTORS
ADJUSTABLE AXLE WIDTH \ TYRES
FLEXIBLE FRONT END
PRINT at 75%  the knuckles have been fitted from a toy car.
SPACE SAVER SNAP IN SERVO
1mm Axles work well
UNIVERSAL AAA BATTERY TRAY
Paperclip for steering and  to lock servo in place with  bumper - 
S1.24 - THE F1 SLED (Forumla 1 Tyre’s)  
55T motor required
WHAT I USE  1.75 filment 210 temps | 200 Max speed  BED TEMP 85
FEATURED MARK. 
SUPER LIGHT
ALL RIGHTS RESERVED 2022 
AMIN SWESSI 3D DESIGNS
S1.24 The Sled
I have an Ender V2.   These are the basic settings i have used to get the desired results.  If you find something better  please share.
USEFUL THINGS TO HAVE
Ready to print at 1/32 1/24 1/18 - PARTS LIST BELOW Best.   
GLUE FROM THE FUTURE XACTO DOUBLE SIDED TAPE HOT GLUE PAPERCLIPS HAND DRILL BITS
S1.32 - PAPERCLIP “FOAM TIRES”  
Snaping the front arms  is ok. Glue them back after the knuckles have been fitted.
DESIGN SOLUTIONS 1 Prepetual Scaling Chassis Design  1 Piece Printing - MINIMAL MATERIAL Snap in Servo Steering Snap in Motor Mount Snap and Superglue Secure Arms Zero Screws Required Standard 2xAAA 2xAA  FAST | STRONG | RESPONSIVE.  — Turn any toy car into a RC with very little parts required. The knuckles, wheels should transfer and any generic 55/110 /130 motor should pop right in, A server and recieved never need more than double sided tape.   
PARTS TO BUY
Drill out the holes.
GEARS + AXLES + MOTORS
PARTS YOU NEED TO FIND
Xacto is your friend
MICRO SERVOS
STEERING KNUCKLES WHEELS AND TIRES MORE WHEELS MORE TIRES AXELS - 2MM OR 3MM 
MICRO RECIEVERS
The parts here will create at least two complete cars. You will still be required to find a 2,4g controlers. The Chassis can be adjust length wise by shortening the front extension. For 1/24 Scale Print 100% - for 1/32 Scale Print at 75% for 1/18 Scale Print at 150%. 
BATTERY
S1.24 - THE F1 SLED (Forumla 1 Tyres)  
QUESTIONS?.   
FEATURED MARK
1/32 PRINT at 75%  the knuckles have been fitted from a toy car.
DESIGN SOLUTIONS 1 Prepetual Scaling Chassis Design  1 Piece Printing - MINIMAL MATERIAL Snap in Servo Steering Snap in Motor Mount Snap and Superglue Secure Arms Zero Screws Required Standard 2xAAA 2xAA  FAST | STRONG | RESPONSIVE.  — Turn any toy car into a RC with as few parts required. The knuckles, wheels should transfer and any generic 55/110 /130 motor should pop right in, A server and recieved never need more than double sided tape.   
UNIVERSAL AA BATTERY TRAY
GLUE FROM THE FUTURE XACTO DOUBLE SIDED TAPE PAPERCLIPS HAND DRILL BITS
The parts here will create at least two complete cars. You will still be required to find a 2,4g controlers. The Chassis can be adjusted length wise by shortening the front extension. For 1/24 Scale Print 100% - for 1/32 Scale Print at 75% for 1/18 Scale Print at 150%. 
I have and Ender V2.   These are the basic settings i have used to get the desired results.  If you find something better  please share.
STEERING KNUCKLES WHEELS AND TIRES MORE WHEELS MORE TIRES AXELS - 2MM OR 3MM  HOT GLUE
12.99 16.99 8.99 9.99 15.99 0.00 2X COMPLETE  1.24 CARS   =   $64.95